全国咨询热线

400-879-1999

点击拨打服务热线:400-879-1999
你所在位置: 首页 >> 新闻中心 > 行业资讯

行业资讯

小型混凝土搅拌车如何进行检修?

作者:http://www.zkzsljbc.com 时间:2021-03-18

对于开搅拌车的朋友来说,肯定都想要有长期的收益,混凝土搅拌车能够工作的年限越长,能够创造出的价值就会越高,所以,检修是小型混凝土搅拌车整个工程作业中也是极为重要的,做好基本的检修我们的工作才能正常进行。
For the friends who drive the mixer, they definitely want to have long-term benefits. The longer the concrete mixer can work, the higher the value it can create. Therefore, maintenance is a small concrete mixer, and it is also very important in the whole project operation. Only by doing a good job in basic maintenance can our work be carried out normally.
图片
picture
将一张#600的砂纸置于ATF油中,浸泡约30分钟。小心地敲击阀体,使卡滞的阀杆从阀腔孔中落下。可能有必要使用一把小螺丝刀,将其撬出。
First, soak a piece of 600 mm sandpaper in ATF oil for about 30 minutes. Carefully tap the valve body to make the stuck stem fall from the valve cavity hole. It may be necessary to pry it out with a small screwdriver.
小型搅拌车
使用螺丝刀时,小心不要划伤阀孔。单向阀杆是否有摩擦痕迹。使用ATF油浸泡过的#600砂纸,打磨阀杆上的毛刺,然后在溶剂中清洗阀杆并用压缩空气吹干。
Be careful not to scratch the valve hole when using a screwdriver. Check whether there are friction marks on the one-way valve stem. Use # 600 sandpaper soaked in ATF oil to grind the burr on the valve stem, then clean the valve stem in solvent and dry it with compressed air.
卷起半张ATF油浸泡过的#600砂纸,将其插入卡滞阀杆的阀孔中。轻轻扭动砂纸,使砂纸松卷,紧密贴合在阀孔表面,然后边推拉,边扭卷砂纸,打磨阀孔。抽出#600砂纸。
Roll up half of ා 600 sandpaper soaked in ATF oil and insert it into the valve hole of stuck valve stem. Gently twist the sandpaper to make the sandpaper loose and tightly fit on the surface of the valve hole, and then roll the sandpaper while pushing and pulling to polish the valve hole. Take out the 600 sandpaper.
图片
picture
在溶剂中彻底清洗整个阀体,然后用压缩空气吹干。在阀杆表面涂ATF油,然后将其落入阀孔中。阀杆应能靠自重落入阀孔底部。否则,重复步骤4,重新测试。如果阀杆仍然卡滞,则更换阀体。
Thoroughly clean the entire valve body in solvent and blow dry with compressed air. Coat the surface of the valve stem with ATF oil and drop it into the valve bore. The valve stem shall be able to fall into the bottom of valve hole by self weight. Otherwise, repeat step 4 and retest. If the stem is still stuck, replace the valve body.
图片
picture
取出小型混凝土搅拌车阀杆,用溶剂彻底清理阀杆和阀体。用压缩空气吹干所有零件,然后用ATF油作为润滑剂,重新组装。
Take out the stem of small concrete mixer and clean the stem and valve body thoroughly with solvent. Dry all parts with compressed air, then reassemble with ATF oil as lubricant.
了解了以上的检修知识,大家可以放心对我们的设备进行检修,大家在选择这些产品的时候我们会有的人士为大家解答,建议大收工时,要彻底清洗混凝土贮罐及进出料口周围,保证不粘有水泥及混凝土结块。
After understanding the above maintenance knowledge, you can rest assured to carry out maintenance on our equipment. When you choose these products, we will have professionals to answer for you. It is suggested that when the work is over, you should thoroughly clean the concrete storage tank and the surrounding of the import and export materials to ensure that there is no cement and concrete caking.
新闻中心
联系我们
  • 公司:莱州聚峰机械有限公司
  • 热线:400-879-1999
  • 地址:山东省莱州市206国道与308省道交叉口东南50米

截屏,微信识别二维码