全国咨询热线

400-879-1999

点击拨打服务热线:400-879-1999
你所在位置: 首页 >> 新闻中心 > 行业资讯

行业资讯

自上料搅拌机中如何利用气流?

作者:http://www.zkzsljbc.com 时间:2021-03-05

气流搅拌是利用气体鼓泡通过液 体层,对液体产生搅拌作用,或使气泡群一密集状态上升借所谓上升 作用促进液体产生对流循环。与机械搅拌相比,仅气泡的作用对液体 进行的搅拌时比较弱的,对于几千毫帕·秒以上的高粘度液体是难于 使用的。但气流搅拌无运动部件,所以在处理腐蚀性液体,高温高压 条件下的反应液体的搅拌时比较便利的。
Gas stirring is the use of gas bubbles through the liquid layer, to produce stirring effect on the liquid, or make the bubble group a dense state rise, by the so-called rising effect to promote the liquid convection circulation. Compared with mechanical stirring, the effect of bubbles on liquid stirring is weaker, and it is difficult to use for high viscosity liquid with several thousand MPa · s. However, there are no moving parts in the air flow stirring, so it is more convenient to deal with corrosive liquid and reaction liquid under high temperature and high pressure.
在工业生产中,搅拌操作时从化学工业开始的,围绕食品、纤维、造纸、石油、水处理等,作为工 艺过程的一部分而被广泛应用。搅拌操作分为机械搅拌与气流搅拌。
In industrial production, mixing operation starts from the chemical industry, and is widely used as a part of the process around food, fiber, paper, oil, water treatment, etc. Mixing operation is divided into mechanical mixing and air mixing.
自上料搅拌车
不要在有孔的分支上使用焊接工具,因为这样会损坏衬层。搅拌机的射孔支管不得使用电焊(气焊)工具,因为电焊会破坏搅拌机的内衬塑料,支管的连接必须用专用管件进行坡口连接;搅拌机的射孔支管不得使用电焊(气焊)工具,因为电焊会破坏搅拌机的内衬塑料,支管的连接必须用专用管件进行坡口连接。
Do not use welding tools on branches with holes as this will damage the lining. Electric welding (gas welding) tools shall not be used for perforating branch pipe of mixer, because electric welding will damage the plastic lining of mixer, and the connection of branch pipe must be beveled with special pipe fittings; electric welding (gas welding) tools shall not be used for perforating branch pipe of mixer, because electric welding will damage the plastic lining of mixer, and the connection of branch pipe must be beveled with special pipe fittings.
在托轮和滚道之间放入木楔,以控制搅拌筒的旋转,一定要注意;将发动机熄火,拆松液压马达的一根高压油管,搅拌筒可自由旋转,控制搅拌筒的旋转,使维修孔转到下部,然后打开维修孔,清理出筒内商品混凝土。此时一定要注意,产品混凝土排出完毕后,恢复商品混凝土水泥搅拌运输车原状。
In order to control the rotation of the mixing cylinder, we must pay attention to putting a wedge between the supporting wheel and the raceway; turn off the engine, remove a high-pressure oil pipe of the hydraulic motor, and the mixing cylinder can rotate freely. Control the rotation of the mixing cylinder to make the maintenance hole turn to the lower part, and then open the maintenance hole to clean up the commercial concrete in the cylinder. At this time, it must be noted that after the discharge of product concrete, the commercial concrete cement mixer truck shall be restored to its original state.
新闻中心
联系我们
  • 公司:莱州聚峰机械有限公司
  • 热线:400-879-1999
  • 地址:山东省莱州市206国道与308省道交叉口东南50米

截屏,微信识别二维码